Roof vents
An exhaust system sized for the attic for a drier attic all year.
A roofer in Ridgewood can install a new roof in the proper sequence: drip edge, ice and water shield, underlayment, starter strip, flashing, vents and then the roofing itself, and most of what makes a roof last happens before the first shingle goes down. Dial (551) 370-0363 to talk with a local roofer about installation.
A quality roofing material can still fail early if it is installed carelessly. Shingles nailed too high above the nail line can blow off in the first strong wind, a missing kickout flashing can rot a wall where the roof meets the siding, and a valley done wrong can funnel water under the roofing. None of these are visible from the ground once the job is done.
Before anything is ordered, the roofer and homeowner settle on the roofing material. Most homes get dimensional asphalt shingles, but metal panels, stone coated steel, tile and slate are all options, and each has its own installation rules. The slope of the roof limits the options, because shingles need a minimum pitch and nearly flat sections need a membrane roof.
It helps to bring a few details to the first conversation. Say whether the job is a tear-off, an addition or new construction, and whether you have a material or color picked out.
Many roof installation calls in Ridgewood also turn up a need for roof replacement or shingle roof installation.
Need roof installation in Ridgewood? Call (551) 370-0363 and describe the problem to a roofer who works in Ridgewood.
Call nowHere is the usual order for installing a shingle roof.
The roof deck must be clean, dry and solid, with any soft plywood or OSB replaced and loose boards renailed. Nails cannot hold in soft wood, so this step is never skipped.
The eaves get drip edge and a band of ice and water shield, and every valley gets a full-width strip. That layering lets water drain off the metal instead of behind it.
Synthetic underlayment or felt covers the rest of the deck, lapped so each row sheds over the one below. Most crews now use synthetic underlayment, which holds up better to foot traffic and weather.
Flashing goes in as the roofing goes up: step pieces at walls, a kickout at the bottom edge and boots on every pipe. Sealant is a backup, not the flashing itself.
A starter strip goes along the eaves and rakes, then shingles are laid in straight courses and nailed in the reinforced nail zone, with four or six nails each as the maker specifies. In cold weather, shingles may need hand sealing because the sealant strips will not bond until warm sun hits them.
Exhaust vents go in near the peak and the ridge is capped. Without enough soffit intake, a ridge vent cannot do its job.
An exhaust system sized for the attic for a drier attic all year.
New flashing at every wall, chimney and vent pipe so the weak points match the new roof.
Starter strip, field shingles and ridge caps, or the panels and trim for a metal roof with fasteners placed where they belong.
Ice and water shield at the eaves and valleys, with underlayment over the rest of the deck acts as the second layer of protection.
Drip edge at the eaves and rakes keeps water off the fascia boards.
New roof installation covers three common jobs: replacing a roof after tear-off, roofing a new home and roofing an addition. On an addition, the tricky part is the tie-in, where new valleys and flashing meet older roofing that may not match. Ask whether the new section will match the existing roofing or whether the whole roof should be redone.
Manufacturers publish exact steps for their products, and local code usually requires following them. A Ridgewood roofer should be able to explain how many nails per shingle will be used, what underlayment goes down and what ventilation the attic will have. Vague answers about the hidden layers are worth noticing.
With an overlay, sometimes called a layover or recover, the new roofing goes on top of the existing shingles. Building codes generally cap asphalt roofs at two layers, so an overlay is only possible on a roof with a single layer, and not over shingles that are badly curled, wet or sitting on soft decking. It saves the labor of a tear-off and keeps the house closed during the job.
An overlay comes with downsides worth weighing. Hidden rot stays hidden, flashing is often reused and the roof carries the weight of two layers. When an overlay is proposed, ask how they confirmed there is only one layer and how the flashing will be handled.
Roof installation in Ridgewood runs from full tear-offs on older homes to brand new roofs on additions and new houses. From Ridgewood out to neighboring communities such as Glen Rock, Midland Park, Waldwick and Hawthorne, roofers see plank decks and thin attic vents on older houses and complex rooflines with many valleys on newer ones, so it is worth asking how each detail will be handled before the first bundle is opened.
For roof installation in Ridgewood, NJ or nearby towns like Glen Rock, Midland Park, Waldwick and Hawthorne, call (551) 370-0363 to reach a roofer who covers your street.
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Ridgewood is busiest after a hard winter and before the next one.
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers in Ridgewood know the roof types and weather wear common in local homes.
Ask your questions before you agree to anything.
More questions? Call (551) 370-0363
A complete new roof from the deck up when repairs no longer make sense, so the house is dry for decades instead of seasons.
Learn moreNew shingle roofs built layer by layer on a sound deck, with nailing and flashing done to the shingle instructions.
Learn moreMetal roof installation built around the right panel, finish and trim for the house, so the roof handles heat, wind and thermal movement.
Learn moreNew construction roofs coordinated with the builder's schedule, planned with ventilation and penetrations in mind.
Learn moreLooking for something else?
See all roofing servicesCall (551) 370-0363 to talk to a roofer serving Ridgewood, NJ.