Framing repair
Damaged structure is repaired for a straight, solid roof.
Metal Roofing
Metal Roof Replacement Ridgewood, NJ
A Ridgewood roofer can tear off an old metal roof, re-cover it with new metal or replace a shingle roof with metal, and help you decide between a tear-off, a re-cover or new panels in just the bad sections. Dial (551) 370-0363 to talk with a local roofer about replacing the roof.
A metal roof needs replacing when the metal itself is failing, not just the screws. When panels are perforated by rust, the finish is gone and every screw hole has been enlarged by years of movement, repairs stop keeping up. Older roofs made from thin, lightly coated steel tend to reach that point first.
There are a few ways to replace a metal roof, and the right one depends on what is underneath. Stripping the old metal exposes the framing, which matters because fasteners in rotten wood will not hold. Retrofit re-covers add a new metal roof over the old one, attached through to the structure.
Many metal roof replacements are actually shingle roofs getting metal for the first time. That job can be a full tear-off or, where code allows, metal laid over one layer of shingles. Have the age, roof type and leak history ready when you call.
If the problem goes deeper than it first looked, a Ridgewood roofer may also recommend metal roof installation or metal roof repair.
Need metal roof replacement in Ridgewood? Call (551) 370-0363 to talk to a local roofer.
Call nowThe process
How metal roof replacement works
The order of work depends on tear-off or re-cover, but the basics are the same.
Inspect the structure
The old roof and the structure beneath it are evaluated for rust, rot and fastener holding power. It also tells whether the framing needs work first.
Choose the approach
The roofer and owner pick the panel profile, metal and color and decide how the old roof will be handled. The new panels are ordered cut to length.
Tear off
The crew unscrews and lifts off the old metal, stacking it for recycling. Sections are opened only when they can be dried in that day.
Repair the framing
The structure is repaired so new fasteners bite into solid wood. Sound framing is what keeps the new roof fastened.
Install the new metal
The roof is dried in, trimmed and paneled, with new boots and flashing at every penetration. Snow guards and ventilation are added where needed.
What is included
Parts of a metal reroof
Tear-off
Failed panels and trim come off section by section.
New panels
New panels in the chosen profile, gauge and finish go on over new underlayment.
New trim
New trim and boots at walls and penetrations so the details last as long as the panels.
Retrofit framing
New panels can be installed over existing metal with fasteners driven into the structure below.
Related service
Metal Roof Panel Replacement Ridgewood, NJ
When only a few panels are rusted through or torn, metal roof panel replacement can keep the rest of the roof in service. The damaged panel is unscrewed, the laps on either side are freed and a new panel of the same profile is lapped in and fastened. Concealed fastener panels take more time to replace because of the seams.
For a Ridgewood building with one or two bad panels, panel replacement is often the sensible step. The new panels may look brighter until they weather. Once a large share of panels need work, replacement becomes the better plan.
Related service
Metal Roof Over Shingles Ridgewood, NJ
Metal over shingles is a common way to switch to metal without stripping the old roof. Where code permits, the roofer adds underlayment or furring strips over the shingles and fastens the metal through to the deck.
The tradeoff is that nobody sees the deck. A roofer in Ridgewood should check the attic for rot and soft spots before recommending it, and the shingles must lie flat enough for the panels. If the deck is questionable or there are already two layers, a tear-off is the better choice.
Local help
Metal Roof Replacement Near Me
Metal roof replacement in Ridgewood covers old barns and shops as well as homes trading shingles for metal. Across Ridgewood and nearby communities including Glen Rock, Midland Park, Waldwick and Hawthorne, metal roofs that went decades without fastener work are the usual replacement jobs, which is why the condition of the purlins and deck drives the plan.
Need metal roof replacement around Ridgewood? Call (551) 370-0363 for a Ridgewood roofer who serves the towns around it too.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Ridgewood is busiest after a hard winter and before the next one.
Why call
Why fix it now
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Ridgewood
Roofers in Ridgewood know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about metal roof replacement
What happens to the old metal roofing?
Metal roofing is one of the most recyclable building materials. The old panels and trim are separated and sent to a recycler. Your roofer can explain how the old metal will be hauled away.
When does a metal roof need replacing instead of repair?
The answer depends on how much of the metal is still sound. If panels are perforated, the coating is gone and the fasteners no longer hold, patches will not keep up. A roofer can tell you which sections can be saved after a look at the roof and the framing.
Can a metal roof be installed over shingles?
Local code decides whether metal can go over existing shingles. It works best when the deck is sound and the shingles lie flat. A roofer can tell you which option fits your house.
How is a single metal roof panel replaced?
One panel can usually be swapped without redoing the roof. The screws and laps are freed, the bad panel slides out and a new panel of the same profile is lapped in with sealant and new fasteners. New panels may look brighter than the old ones at first.
What is a metal roof retrofit?
A retrofit, or re-cover, installs new metal over the existing panels using a sub-framing system. The method is popular on commercial buildings and large outbuildings. An engineer or roofer confirms the framing can carry the added load.
More questions? Call (551) 370-0363
Related services
Metal Roof Installation
Metal roof installation built around the right panel, finish and trim for the house, so the roof handles heat, wind and thermal movement.
Learn moreMetal Roof Repair
Metal roof repairs that stop leaks at the screws, laps and flashing, so the panels keep shedding water for years more.
Learn moreRoof Replacement
A complete new roof from the deck up when repairs no longer make sense, so the house is dry for decades instead of seasons.
Learn moreStanding Seam Metal Roof
Standing seam metal roofing installed, repaired and detailed for thermal movement, for homes, additions and low slope roofs.
Learn more
Looking for something else?
See all roofing servicesTalk to a Ridgewood roofer about metal roof replacement
Call now for Ridgewood metal roof replacement and help in the towns around it.