Rust treatment
Rust is removed and primed for long-lasting protection.
Metal Roofing
Metal Roof Coating Ridgewood, NJ
A roofer in Ridgewood can coat an aging metal roof with an elastomeric or silicone system that seals screw heads and laps, covers surface rust and reflects sun, when the metal underneath is still solid. Call (551) 370-0363 to reach a local roofer.
A coating renews a metal roof whose finish has worn away but whose panels are still sound. By the time a metal roof is a coating candidate, the paint is usually chalky, rust has started at screw heads and seams and a few fasteners leak. Rusted-through panels and rotten purlins have to be fixed before any coating goes on.
Most metal roof coatings are acrylic or silicone. Elastomeric acrylic coatings are durable and easy to recoat, and they work well where roofs drain freely. Silicone handles ponding water and UV well but bonds poorly to anything but more silicone later.
Most coating failures come from skipped prep, not bad material. The roof has to be cleaned of chalk, dirt and oil, rust has to be treated, and fasteners and seams have to be sealed before the base coat goes on. The work needs a stretch of dry, mild weather.
If the problem goes deeper than it first looked, a Ridgewood roofer may also recommend metal roof repair or roof coating.
Need metal roof coating in Ridgewood? Call (551) 370-0363 and describe the problem to a roofer who works in Ridgewood.
Call nowThe process
What happens during a metal roof coating
Here is how a roofer usually coats a metal roof.
Assess the candidate
The roofer checks for rust-through, loose panels, rotten purlins and the condition of the fasteners and finish. Test patches help pick the right primer.
Remove chalk
The roof is washed to remove chalk, dirt, oil and loose paint, often with a cleaner made for coating prep. Everything has to be dry before primer goes on.
Treat the rust
Surface rust is cleaned and sealed with primer. Galvanized or heavily rusted roofs may get a full primer coat.
Seal fasteners
Screws and laps are sealed and reinforced so the coating spans them without cracking. These details are where leaks usually start.
Base coat
The coating is applied in one or more coats to reach the right dry film thickness. Correct thickness is what gives a coating its life span.
What is included
A complete metal coating job
Surface prep
Old loose paint is cleaned off for good adhesion.
Reflective coating
A flexible coating covers the whole roof and helps keep the building cooler.
Screw encapsulation
Each screw head is sealed so washers are no longer the only barrier.
Seam reinforcement
End and side laps are sealed with embedded polyester fabric.
Related service
Metal Roof Restoration Ridgewood, NJ
Metal roof restoration is the full process of bringing a worn metal roof back into service, and the coating is the last step. It typically includes replacing rusted-through panels, swapping worn fasteners, resealing laps, fixing trim and flashing and then applying the coating.
A metal roof restoration in Ridgewood makes sense when the framing and most panels are still in good shape. It also skips tear-off and disposal of the old metal. Ask what prep is included and what coating thickness is planned.
Related service
Metal Roof Painting Ridgewood, NJ
Painting a metal roof refreshes the finish with a thin layer of direct-to-metal paint. Because paint is thin, it protects metal but cannot stop active leaks.
For a Ridgewood metal roof that is dry but faded, painting can be the right fit. Prep is the same: clean, treat rust and prime before painting. For roofs with leaks, ask about a full coating instead of paint.
Local help
Metal Roof Coating Near Me
Around Ridgewood, coatings are often chosen for metal roofs that are sound but tired. From Ridgewood out to neighboring towns such as Glen Rock, Midland Park, Waldwick and Hawthorne, coatings let owners of solid but weathered metal roofs avoid a full replacement, which is why an inspection before rust spreads is so useful.
For metal roof coating in Ridgewood, NJ or nearby towns like Glen Rock, Midland Park, Waldwick and Hawthorne, call (551) 370-0363 to reach a roofer who covers your street.
How the weather here affects roofs around Ridgewood
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Ridgewood is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Local roofers see the same roofs and storm damage across Ridgewood and nearby towns.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about metal roof coating
Silicone or acrylic: which coating is best for metal?
The usual choices are elastomeric acrylic and silicone. Acrylic is flexible, reflective and easy to recoat, and it suits sloped roofs that drain well, while silicone handles ponding water and sun but only bonds well to more silicone later. The roof slope, climate and future plans decide which fits.
What is the difference between painting and coating a metal roof?
A coating is many times thicker than paint and stretches to seal seams and fasteners. Choose a coating for leaks and paint for appearance. Prep matters equally for both.
Is my metal roof a good candidate for coating?
A coating works best on a metal roof that is worn on the surface but sound underneath. If panels are rusted through across the roof, replacement is usually better. An inspection with an adhesion test answers the question.
Will a coating stop my metal roof from leaking?
A full coating system can stop leaks at screws and seams when the prep is done right. Rust holes and loose panels have to be repaired first, since a coating will not span a hole or hold a loose panel down. An inspection shows whether a coating will solve your leaks.
When will a coated metal roof need recoating?
A coating applied at the right thickness typically lasts ten to twenty years. Thicker applications last longer, and recoating before the coating wears through renews it without starting over. Watch for thinning or chalking as signs a recoat is near.
More questions? Call (551) 370-0363
Related services
Metal Roof Repair
Metal roof repairs that stop leaks at the screws, laps and flashing, so the panels keep shedding water for years more.
Learn moreRoof Coating
Liquid-applied roof coatings that seal seams, reflect heat and add years to a roof, after the seams and blisters are repaired.
Learn moreCommercial Roof Coating
Fluid-applied roof coatings that restore aging membranes and metal, built to a measured thickness.
Learn moreMetal Roof Inspection
Metal roof inspections that look at screws, laps, rust, closures and the underside of the panels, before small fastener problems become leaks.
Learn more
Looking for something else?
See all roofing servicesGet metal roof coating help in Ridgewood
Call (551) 370-0363 for a local roofer in Ridgewood and nearby towns.