Gutter rehanging
Sagging gutters are rehung on solid fascia with new hangers with screws instead of loose spikes.
Exterior Services
Fascia Repair Ridgewood, NJ
A Ridgewood roofer can repair the fascia boards that carry your gutters and cap the ends of the rafters, so the gutters have solid wood to hang from again. Dial (551) 370-0363 to talk with a local roofer about the fascia.
When a fascia board goes soft, the cause is almost always water running down the back of the gutter instead of into it. Without a drip edge lapped into the gutter, runoff clings to the roof edge and wets the top of the fascia every storm. The wood slowly loses strength until the gutter spikes or hanger screws no longer hold.
Fascia damage does not stay in the fascia for long. Left alone, the rot moves into the rafter ends and the edge of the roof deck, which turns a trim repair into structural work. Aluminum wrap over wood can hide all of this, since the metal looks fine while the board behind it crumbles.
A few observations make the first conversation more useful. Look for sections where the gutter tips forward, where the board looks dark or swollen and where paint is flaking. Say whether the fascia is bare wood, painted, PVC or wrapped in metal, since that changes the repair.
Fascia Repair is often paired with soffit repair and gutter installation, depending on the cause.
Looking for Ridgewood fascia repair? Call (551) 370-0363 and describe the problem to a roofer who works in Ridgewood.
Call nowThe process
How fascia repair works
Here is how a roofer typically handles a fascia repair.
Find the water path
The visit starts with where the water comes from, usually a missing drip edge, a clogged gutter or a gutter with the wrong slope. Probing along the board shows where the rot starts and stops.
Remove the gutter
Gutters are taken down along the damaged stretch, which also shows how well the hangers were holding. This is a good time to check the gutter itself for leaks and bad seams.
Check the rafter tails
Soft rafter tails are cut back and sistered with new lumber, and rotted decking at the edge is replaced. This is the step that decides whether the repair lasts.
Install new fascia
The new board is fastened to the rafter tails with corrosion-resistant nails or screws, with tight joints at the corners. PVC and composite boards do not rot and hold paint well.
Fix the edge flashing
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. Without it, the same board will rot again.
Reattach gutters
Gutters are rehung on the new fascia with a slight slope toward the outlets. Wood fascia gets a finish coat of paint.
What is included
Fascia repairs a roofer can handle
Drip edge installation
New drip edge is tucked under the shingles over the gutter to keep runoff off the fascia.
Fascia wrapping
Coil stock wrap is bent to fit over solid boards to cut down on painting.
Soft fascia
Rotted sections of fascia are cut out and replaced with new boards and scarfed into the existing board.
Framing repair
Rotted rafter ends behind the fascia are sistered or rebuilt before the fascia goes back on.
Related service
Fascia Board Replacement Ridgewood, NJ
When rot runs along most of a wall, or the boards are split and warped end to end, replacing the full run of fascia is the cleaner fix. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. It is also the moment to choose a material, whether primed wood, PVC, composite or wood with an aluminum wrap.
For many Ridgewood homes it makes sense to replace fascia while the gutters are off for replacement anyway. Make sure rotted boards are removed, not covered. Also ask about the size of the new boards, since fascia that is too narrow can leave gaps at the soffit and gutter.
Related service
Fascia Board Repair Ridgewood, NJ
When rot is confined to short stretches, the damaged part of the board can be cut out and a new piece scarfed in. Angled joints hold paint and shed water better than straight cuts, so they are the standard for patch repairs. Very small areas of surface rot can sometimes be treated with a wood consolidant and exterior filler, then primed and painted.
Patching a fascia board in Ridgewood without fixing the gutter or drip edge above it just buys a season or two. That usually means resealing a gutter seam, unclogging a downspout or adding drip edge over the repaired section. Once the wood is primed and painted on all sides, a repaired section can last as long as the rest of the board.
Local help
Fascia Repair Near Me
In Ridgewood, fascia tends to fail first on the sides of the house where gutters clog fastest. Homes in Ridgewood and nearby towns like Glen Rock, Midland Park, Waldwick and Hawthorne range from older houses with wood fascia that needs regular paint to newer builds where metal wrap can hide rot underneath, so a look along the roof edge each spring and fall helps catch soft spots early.
Searching for fascia repair near me from Ridgewood or Glen Rock, Midland Park, Waldwick and Hawthorne? Call (551) 370-0363 to talk to a roofer who works in your part of town.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Ridgewood, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Ridgewood
Local roofers see the same roofs and storm damage across Ridgewood and nearby towns.
Straight answers
Ask your questions before you agree to anything.
Fascia Repair questions
Should I cover rotted fascia with metal?
Wrapping over soft fascia traps moisture and lets the rot continue unseen. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Fix the wood, then add wrap over it.
What is the best material for fascia?
Rot-proof materials such as PVC and composite last longest. Primed wood is easy to match on older homes but needs regular paint. No material holds up if water keeps running behind the gutter.
Do fascia boards affect my gutters?
The fascia is what gutters are fastened to. When the wood softens, hanger screws and spikes lose grip and the gutter sags, tips forward or pulls away. The fix is solid wood plus new hangers, pitched toward the downspout.
Why is my fascia rotting?
Water getting behind the gutter is the main cause. Clogs, bad seams and the lack of a drip edge are the usual culprits. Peeling paint and unsealed cut ends speed up the damage.
Do I need new fascia boards or just a repair?
Short sections of rot can be repaired by cutting out the bad wood and scarfing in a new piece. Long stretches of soft wood are better handled by replacing the whole board. Either way, the rafter tails behind the board need to be checked.
More questions? Call (551) 370-0363
Other services that may help
Soffit Repair
Repairs for rotted, sagging or loose soffit panels under the roof eaves, before rot spreads into the fascia and rafter tails.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Gutter repair for leaking seams, sagging runs, loose hangers and broken downspouts, without replacing gutters that still have life in them.
Learn moreRoof Repair
Repairs for missing shingles, lifted tabs, cracked pipe boots, loose flashing and soft decking, matched to what is actually wrong up top.
Learn more
Looking for something else?
See all roofing servicesTalk to a Ridgewood roofer about fascia repair
Call (551) 370-0363 to talk to a roofer serving Ridgewood, NJ.